This item is for one (1) one hundred (100) gallon per day Reverse Osmosis membrane by CSM
CSM reverse osmosis membrane elements for home drinking water are the industry's most reliable. Advanced membrane technology and automated fabrication allow these elements to deliver consistent performance that equipment suppliers, water treatment dealers, and residential customers can rely on. CSM elements are shipped dry for convenient handling and long shelf-life. These elements are NSF listed.
CSM RESIDENTIAL Membranes
RO elements for residential use (1.8 and 2.0 inch diameters)
Model RE1812-24 - Flow 24 - Reject 98% - Diameter 1.8 in - Length 12 in - Test Cond. 60 psi/250ppm - Temp 77 F
Model RE1812-35 - Flow 35 - Reject 98% - Diameter 1.8 in - Length 12 in - Test Cond. 60 psi/250ppm - Temp 77
Model RE1812-50 - Flow 50 - Reject 98% - Diameter 1.8 in - Length 12 in - Test Cond. 60 psi/250ppm - Temp 77
Model RE1812-80 - Flow 80 - Reject 98% - Diameter 1.8 in - Length 12 in - Test Cond. 60 psi/250ppm - Temp 77
Model RE1812-100 - Flow 100 - Reject 98% - Diameter 2.0 in - Length 12 in - Test Cond. 60 psi/250ppm - Temp 77
1. The stated product performance is based on data taken after 30 minutes of operation at the following
* 250 mg/L NaCl solution at 60 psig (0.41 MPa) applied pressure
* 15% recovery
* 77 oF (25 oC)
* pH 6.5-7.0
2. Dry type elements are vacuum leak tested using the San Diego Protocol.
3. Permeate flow rate for each element may vary but will be no more than 15% below the value shown.
4. All elements are packaged in a polyethylene bag containing 1.0% SBS (sodium bisulfite) solution.
Membrane type: Thin-Film Composite
Membrane material: Polyamide (PA)
Element configuration: Spiral-Wound, Tape Wrapping
(See picture diagram above for A, B, C, D and E)
Model RE1812-24 - A .67 in - B .87 in - C 11.73 in - D 1.77 in - E .98 in
Model RE1812-35 - A .67 in - B .87 in - C 11.73 in - D 1.77 in - E .98 in
Model RE1812-50 - A .67 in - B .87 in - C 11.73 in - D 1.77 in - E .98 in
Model RE1812-80 - A .67 in - B .87 in - C 11.73 in - D 1.77 in - E .98 in
Model RE1812-100 - A .67 in - B .47 in - C 11.73 in - D 1.91 in - E .98 in
A) Diameter of center feed post
B) Length from end of feed post to membrane wrap
C) Over-all length from end of feed post to end of Permeate post
D) Diameter of membrane wrap
E) Length from membrane wrap to end of Permeate post
Increase The GPD Capacity of Your RO System
A membrane upgrade is actually quite easy on most reverse osmosis systems. Simply replace the membrane with the desired capacity and then properly size the flow restrictor to match the capacity of the membrane. These must be matched to keep the proper water flow over the membrane surface. Mis-matched membranes and flow restrictors will either cause excessive waste to the drain or premature membrane fouling. You will find flow restrictors to match the RO membranes we offer here on our web site.
Convert "Proprietary" RO Membrane to Standard
Many owners of "proprietary" style RO systems convert their systems to use a standard membrane housing and a standard RO membrane and in doing so they save a bundle of money and the product is easier to find. Visit our FAQ section here on our web site or contact us and we will answer your questions about converting your "proprietary" (non-standard) RO system to a standard system.
Check our Components & Parts
category to build your own water filter unit or to acquire replacement items for your Reverse Osmosis
system or Water Filter System
. We have hundreds of water equipment items to meet your needs to replace or upgrade your water system.